Electronics & Communication / DSB-SC Balanced Modulator
FREE TO EXPLORE
LABORATORY 03 · ELECTRONICS & COMMUNICATION

Double-Sideband Suppressed-Carrier (DSB-SC) Modulation via Balanced Ring Modulator

Synthesize a DSB-SC modulated signal using a diode ring balanced modulator, evaluate carrier suppression ratio in dB, and measure RF output amplitude versus modulating tone amplitude. Explore interactive telecommunication simulation, RF analysis, and signal processing telemetry.

ANALOG MODULATION · DIGITAL BASEBAND · PASSBAND MODULATION · ANTENNAS & RF · OPTICAL FIBER · DSP

Your virtual electronics & communication engineering laboratory.

DSB-SC PEAK-TO-PEAK OUTPUT AMPLITUDE V_DSBSC—
RF INSTRUMENTATION TELEMETRY

Ready to sample with Modulating Amplitude = 2.0 V.

2.0 V
Excitation locked to low-phase-noise synthesized reference oscillator.

Adjust Modulating Amplitude, then execute telecommunication RF/baseband acquisition.

Communication telemetry is sampled with calibrated high-precision instruments using 64-bit IEEE 754 precision buffers. Residuals reflect ordinary least-squares regression across successive observations. Continuous data structures support high-fidelity modulation, channel, and spectral analysis.

Communication engineering assumptions and boundary limits

Channel modeled under additive white Gaussian noise (AWGN) and linear band-limited propagation. Harmonic distortion remains constrained below -45 dBc across all calibrated test points.

Laboratory apparatus & testing equipment.

DSB-SC Balanced Modulator Telecommunication Workstation

Provides regulated RF/baseband excitation, precision impedance-matched test fixtures, and low-noise interconnection for carrier null balance, spectrum analyzer phase inversion & product detection.

6.5-Digit True-RMS Digital Multimeter (Keysight / Fluke)

Measures DC bias points, RMS carrier/signal voltages, and circuit node potentials with ±0.0035% baseline accuracy.

Four-Channel Digital Storage Oscilloscope (200 MHz, 2 GSa/s)

Captures high-frequency RF envelopes, baseband eye diagrams, constellation patterns, and transient responses for dsb-sc balanced modulator.

Synthesized Vector RF Signal Generator (9 kHz – 3 GHz)

Delivers calibrated, low-phase-noise continuous-wave and modulated carrier signals to establish modulating amplitude conditions.

High-Dynamic-Range RF Spectrum Analyzer (9 kHz – 3.6 GHz)

Quantifies fundamental harmonic amplitudes, carrier suppression ratios, sideband power distributions, and spurious emissions.

Matched 50-Ohm Coaxial Interconnects & Attenuator Set

Maintains uniform transmission line impedance, eliminates unwanted standing-wave reflections, and protects instrument front-ends.

FOLLOW THE METHOD

A reason behind every step.

Synthesize a DSB-SC modulated signal using a diode ring balanced modulator, evaluate carrier suppression ratio in dB, and measure RF output amplitude versus modulating tone amplitude. Standardized parameter settings: 0.5, 1.0, 1.5, 2.0, 3.0, 4.0 V.

  1. Apparatus Calibration & Ground Plane Verification: Inspect all coaxial BNC/SMA interconnects and verify 50-ohm characteristic termination. Power up all instruments and allow a 20-minute thermal settling period to stabilize crystal reference oscillators.
  2. Carrier & Modulating Signal Synthesis: Configure the synthesized RF signal generator and baseband source to the specified baseline parameters. Calibrate the modulating amplitude using the precision digital multimeter and oscilloscope.
  3. Systematic Telemetry Acquisition & Setpoint Stepping: Increment the modulating amplitude systematically across the experimental range (0.5 to 4.0 V), logging the resulting dsb-sc peak-to-peak output amplitude v_dsbsc after signal settling.
  4. Frequency-Domain & Time-Domain Cross-Validation: Observe and photograph the corresponding waveform on the digital storage oscilloscope and verify the spectral distribution on the RF spectrum analyzer. Verify that harmonic distortion remains below -45 dBc.
  5. Repeatability & Hysteresis Verification: Execute both ascending and descending parameter sweeps across the device under test (DUT) to detect any thermal drift, detector non-linearity, or oscillator pulling.
  6. De-energization & Dataset Archival: Safely reduce RF excitation levels, save captured digital waveforms to non-volatile storage, export telemetry to the laboratory logbook, and power down all high-frequency instrumentation.
YOUR NOTEBOOK · 0 OBSERVATIONS

Turn measurements into telecommunication engineering insight.

See a complete example report ↗

Points are your recorded observations. The solid regression line validates DSB-SC Balanced Modulator mathematical scaling.

LINEAR REGRESSION FIT · y = mx + b
V_dsbsc = 1.5000 · V_m
#Modulating Tone Amplitude V_m (V)DSB-SC Peak-to-Peak Output Amplitude V_dsbsc (V)Modulating tone amplitude V_m (V)DSB-SC output amplitude V_dsbsc (V)

No readings yet. Execute a communication trial and record it.

CHECK YOUR UNDERSTANDING

Explain what the communication metrics mean.

Question 1: In the experimental investigation of DSB-SC Balanced Modulator, the primary dependent variable measured is:

Question 2: The mathematical relationship governing DSB-SC Balanced Modulator is modeled as:

Question 3: The target benchmark parameter derived from regression analysis is:

Question 4: Which instrument provides the most accurate visualization of spectral harmonics and carrier sidebands in the frequency domain?

THEORY AND ELECTROMAGNETIC CONTEXT

Electronics & Communication Engineering background & physical principles.

Synthesize a DSB-SC modulated signal using a diode ring balanced modulator, evaluate carrier suppression ratio in dB, and measure RF output amplitude versus modulating tone amplitude.

V_dsbsc = 1.5000 · V_m

Communication systems rely on Fourier spectral decomposition, Shannon channel capacity, and electromagnetic propagation theory.